Products -> ACCESSORIES (*)
* Sorry for the inconvenience, we are upgrading our WEB site.
|
 |
HIGH TENSION CONVERTER FOR ELETRIC SPARK IGNICION
 »» ACS-TE-C5
For electric spark ignition of gas burners. Voltage
115 or 220V - Power 8 VA - secondary voltage 23 Kv - Scheme of service:
Intermittent 33% - Operating temperature of 0 to 60ºC.
Replaces model
ACS-TE-21-C4 (stays for replacement) and is no longer recommended for new
designs, the Selcon.
See specifications and order codes: 
|
|
|
 |
HIGH TENSION CONVERTER FOR ELETRIC SPARK IGNICION
»» ACS-TE-C6
For electric spark ignition of gas burners or light
liquid fuels. Power 120 or 230V +10% -15 - Power 8 Kvef (26 Kvpp) - 35mA. -
Scheme of Service: Intermittent 50% - Operating temperature: 0°C to 60ºC.
Replaces the models ACS-C1-TE, TE-ACS and ACS-C2-C3-TE (remain for
replacement) and are no longer recommended for new designs by Selcon.
See specifications and order codes:
|
|
|
 |
ELECTRODE FOR ELETRIC SPARK IGNICION
SEL-HT-C
Electrode for flame sensor (ionization) or ignition. With or without securing
thread, with or without protective cover.
120 mm porcelain and 500 mm free
length of the electrode / 50 mm porcelain and 140 mm free length of the
electrode.
SEL-HT-E
Sensors and electrodes assembled as required by the client’s drawing or sample –
SPECIAL.
See specifications and order codes:
|
|
|
 |
HIGH TENSION ELETRONIC PORTABLE IGNITOR
ACS-IP
High-Voltage Portable Igniter for Gas Burner
Spark Ignition.
See specifications and order codes:
|
|
|
 |
TIMED IGNICION PANEL FOR BURNER
ACS-IT
Ignition panel with timer for burners.
See specifications and order codes:
|
|
|
 |
IGNICION CABLE
ACS-CB-C1521-O
High-insulation cable for ignition of interconnection of ionization
sensor; Neoprene; Operating temperature: up to 130°C.
See specifications and order codes:
|
|
|
 |
IGNICION CABLE
ACS-CB-C2541
High-insulation cable for ignition of interconnection of ionization
sensor; Silicone; Operating temperature: up to 300°C.
See specifications and order codes:
|
|
|
 |
ELECTRODE CONNECTOR / HIGH TENSION CABLE WITH TOUCH PROTECTION
ACS-CP
Connector for
electrode/high voltage cable, with touch protection.
Nitrile (up to 100ºC) or
Silicone (up to 200º C).
See specifications and order codes:
|
|
|
 |
PILOT BURNERS
Reform and Maintenance of Burners Pilots.
Custom. Contact us.
|
|
|
 |
ARTICULATED CONNECTION FOR OPTICAL FLAME SENSOR
ACS-CN-C1
This connection is adequate to sensors with or without
self checking. It uses a standardized flange as the base, allowing the user to make the
counter-flange installation even before receiving the part. It enables to
improve, during the start-up and any time later, the sensor view of the flame
and provides an input for cleaning/cooling air connection. It is recommended
where the flame position, in its point of highest stability of radiation
emission, is not 100% known. It may be used with all sensors of SEL-SV line
manufactured by Selcon.
See specifications and order codes:
|
|
|
 |
FIXED CONNECTION FOR OPTICAL FLAME SENSOR
ACS-CN-C3
Fixed connection for flame
sensor.
See specifications and order codes:
|
|
|
 |
STANDARDIZED SIGNAL CONVEYOR (4-20mA)
ACS-CV
It converts the flame signal into the standardized
signal of 4-20 mA., for the dynamic signaling of the flame
status, from the site/view tube perspective, where the sensor is mounted
See specifications and order codes:
|
|
|
 |
FLAME PRESENCE SIGNAL CONVEYER
ACS-TX
TRANSMITTER OF FLAME PRESENCE SIGNAL -
Allows distant transmission of flame presence signal sent by SEL-SV and SEL-HT
line sensors.
See specifications and order codes:
|
|
|
 |
MONITORING PROGRAMMER FOR PARAMETERS OF THE MCQ SYSTEM
ACS-PG-MCQ
The ACS-PG-MCQ programmer
allows supervision of the multifuel/MCQ burner system parameters, together with
CHM-F-MCQ flame presence detector relay and SEL-SV-MCQ sensor-transmitter
(weatherproof
or explosion-proof) making this unit the man-machine interface (MMI) of the MCQ system.
See specifications and order codes:
|
|
|
 |
CABINET FOR ELETRONIC EQUIPAMENT ASSEMBLY
ACS-CS-C20
Cabinet for electronic equipment assembly.
See specifications and order codes:
|
|
|
 |
CONTROL OR POWER CABLE, TRANSMISSION CABLE FOR FLAME PRESENCE SIGNAL OR CONTROL IN GENERAL
ACS-CB-C3:
Used as power or control cable in general. Operating temperature: up to
75°C.
See specifications and order codes:
ACS-CB-C4217:
Transmission cable of flame presence signal or for serial communication of
MCQ system.
See specifications and order codes:
ACS-CB-C4517:
Recommended for use as a cable transmitting the
signal of presence of flame, serial communication via RS 485 (two pairs of
conductors) between the transmitter and sensor-relay flame detector, members of
the security system calls, online MCQ.
See specifications and order codes:
|
|
|
 |
HIGH TENSION CONVERTER FOR ELETRIC SPARK IGNICION
Remain for replacement and are no longer recommended by Selcon for new projects.
ACS-TE-C1
Electronic ignition transformer for gas or light oil. 115 or 220 VAC, 50 or 60
Hz, 10,000 Vpp, 100VA.
See specifications and order codes:
ACS-TE-C2
Electronic ignition transformer for gas or light oil. 115 or 220 VAC, 50 or 60
Hz, 10,000 Vpp, 60VA.
See specifications and order codes:
ACS-TE-C3
High-voltage transformer for gas burner spark ignition. 220 VAC, 50 OR 60 Hz,
10,000 Vpp.
See specifications and order codes:
ACS-TE-C4
Electronic ignition transformer for gas or light oil. 115 or 220 VAC, 50 or 60
Hz, 10,000 Vpp, 8VA.
See specifications and order codes:
|
|
|
